Biofa Primasol Velouté White 3011

Description

Velvety aspect (mat-satin), washable,good coverage, solvent-free, microporous, based on natural materials. For interior applications.
Available in white; can be tinted with BIOFA 3601-3616 color pastes, BIOFA 1301-1317 powder pigments or NCS and RAL color charts to order; ready to use.

Use

• Gypsum, plasterboard, plaster, woodchip paper, concrete, etc.
• Can be used to renovate old dispersion paints.

Instructions for use

1. Substrate preparation: the substrate must be dry, clean, free from grease stains and prepared according to the rules of the trade.
   Remove loose old paint, limewash or glue.
   Clean and sand old latex or acrylic paints.
   On crumbly or highly absorbent substrates, first apply a coat of BIOFA 1440 WALL FIXER.
   Lightly absorbent substrates: dilute paint to max. 100% water.
   For concrete or cement surfaces, wait at least 6 weeks. Follow the instructions in the table overleaf.
   Surfaces that have been stripped should be sanded (60-100 grit), vacuumed and dusted, or brushed with hot water. Treat after 24 h with a coat of BIOFA 1440; residues of wallpaper paste may cause adhesion problems.
   Note: it is possible that rust, nicotine or other stains may show through on substrates previously treated with water-based systems. Test first.
2. Primer: mix well. For the first coat, add up to 5% water.
   On paper to be painted or light surfaces to be refreshed, a single coat may be sufficient.
   Apply with a brush or medium nap roller. Airless spray system: 0.53 mm nozzle, 200 bar pressure.
   Important: apply evenly!
   Work the edges 'wet in wet'!
   Use soft rollers that can take enough paint!
   Try it out!
   During application and drying, ensure good ventilation.
   Do not work below 12°C.
3. Top coat: apply an additional coat of PRIMASOL to improve coverage.
4. Cleaning equipment: clean tools with BIOFA 0600 brush cleaner and rinse with clean water.

Drying

Dry after 2 to 4 hours.
Can be recoated after approx. 12 hours.

Wait at least 24 hours before covering with wall glazes (20°C/50-55% relative humidity). In the case of low or non-porous substrates, glazes may take 5 to 6 days to dry. Try it out!

Composition

Water, chalk, titanium dioxide, mixed mineral powders of chlorite, glimmer and quartz, pure acrylate, potassium silicate, sodium phosphonate, starch, potassium methylsiliconate, polyether derivatives of fatty acids, ammonia complex.

Consumption

For normal porosity: 160-200ml/m² or 5-6m²/litre.

Storage

Store in a cool, frost-free place. Open cans should be used as soon as possible. Original closed cans are stable for at least one year. Caution: exposed to heat, product may thicken.

Safety advice

Natural products should be kept out of the reach of children.
Alkaline product. Protect eyes and skin, glass surfaces, natural stone, aluminum, wood and lacquer. If splashed in eyes, rinse thoroughly. In case of splashes on lacquered, metallic, plastic-coated, glass or ceramic surfaces, etc., wash immediately with water.
Store in a cool, dry place, away from frost.
Keep out of reach of children.
Do not breathe spray mist.

Recycling

Do not dispose of residues down the drain or in the ground.
Liquid product should be disposed of in paint containers or in accordance with local regulations.
Small quantities and dry rags can be disposed of in household waste.
Empty, dry packaging should be disposed of at a waste disposal center.
Unfit packaging must be treated in the same way as the product!

VOC EU-max. (cat. A/g) : 30 g/L (2010)
3046 contains max. 0 g/L

Recycling: Liquid waste EAK 080112